Browse By
Category
  1. Connectors (4)
  2. Routers (7)
  3. WLAN (20)

Connection

Grid List

10 of 28 products

per page
Page:
  1. 1
  2. 2
  3. 3
  1. Digi Connect Sensor with low power

    Digi Connect Sensor with low power

    Digi International, has presented Digi Connect Sensor, a battery-fueled, endeavor prepared, cell portal answer for remote availability at areas with either no power or low power.

    In offering an attachment and-play arrangement, Connect Sensor takes into consideration remote sensor observing to be conveyed in conditions beforehand considered excessively cruel, remote or not financially suitable. With adaptability and adaptability to suit off-the-rack sensors, for example, stream, level, weight and ecological conditions, the recently reported cell passage arrangement will help make sensor utilize universal.

    Call for price
  2. iSOLATE501 Intrinsically Safe Ultra-Wide Band RF Galvanic Isolator
    II (1) GD [Ex ia Ga] IIC, [Ex ia Da] IIIC I (M1) [Ex ia Ma] I cMETus Class I, II, Div 2, Class III Div 1 & 2, Groups A-G. Class 1, Zone 0, Group IIC T4 -40°C ≤ Ta ≤ +80°C
    Call for price
  3. iSiS1700Sa safe area fiber optic to Cat5 media converter
    The iSiS1700Sa is intended for use in Safe Areas. The two fiber-optic ports are designated ‘Ex op is’ – meaning the transmitted optical power is deemed inherently safe according to IEC 60079-28:2015. Therefore the fiber cables can pass into Zone 2 and Zone 1 areas and connect to suitably approved and compatible link-partners such as HMIs. The iSiS1700Sa functions as an un-managed Ethernet switch with both fiber and copper ports inter-connected internally. No configuration is necessary.
    Call for price
  4. ATEX Zone 1 WLAN Access Point Series 9710

     

    The ISwireless WLAN access point Series 9710 is an access point for industrial use which has an Ethernet 100 Base-T connection. The device has a bit rate of up to 54 Mbit/s and supports the standards IEEE 802.11b/g (2.4 GHz ISM band) and 802.11a (5 GHz ISM band). Since it has been designed for the international use, it has many features which qualify it for the industrial use in the process industry.
     
    Call for price
  5. ATEX Zone 1 WLAN Access Point Series 8265
     
    The WLAN Access Point from R. STAHL stands out due to its easy installation and a robust enclosure which is suitable for rough industrial environments. Its wide temperature range allows to be used almost under all conditions.
    Call for price
  6. ATEX Zone 1 POE Ethernet Extender
    The A290001 POE/ Ethernet Extender is ATEX certified and doubles, triples or even quadruples the normal 330ft (100m) CAT5 cable run length for 100BaseT networks.
    Call for price
  7. ATEX Zone1 Access Point iWAP107

     

    The ATEX iWAP107 gives you the advantages of MIMO technology for the hazardous process areas. This allows the latest MIMO Access Points from market leaders such as Cisco and Aruba to be cost-effectively deployed; significantly improving Wi-Fi performance and reliability.
    Call for price
  8. ATEX Explosion Proof Connector iSOLATE-CT

     

    The ATEX iSOLATE-CT is designed for use with the  ATEX iSOLATE500 range of galvanic RF isolators to enable quick & simple wireless deployments in hazardous areas 

    Call for price
  9. AWK-5222
    The new generation wireless redundancy technology allows you to set up independent wireless connections to avoid interruptions in transmission, even if interference occurs on one of the supported frequencies. The AWK-5222 is equipped with the newest proprietary wireless redundancy technology, which has two independent RF modules, and supports a greater variety of wireless configurations and applications. The redundant wireless connections increase the reliability of the entire wireless network. For reliability beyond wireless redundancy, Moxa’s AWK-5222 has two Ethernet ports, and supports RSTP (Rapid Spanning Tree Protocol). The AWK-5222 is rugged enough to help you establish the most robust wireless connection for critical industrial wireless applications.
    Call for price
  10. AWK-4121
    The AWK-4121 outdoor wireless AP/bridge/client is the ideal outdoor wireless solution for industrial applications that are hard to wire, too expensive to wire, or use mobile equipment that connect to a TCP/IP network. The AWK-4121’s dust-tight/weatherproof design is IP68-rated, allowing you to extend existing wired networks to outdoor locations and critical environments. The two redundant DC power inputs increase the reliability of the power supply and can be powered via PoE for easier deployment. The AWK-4121 is compliant with the essential sections of EN 50155, covering operating temperature, power input voltage, surge, ESD and vibration. With many hardened industrial-grade features, the AWK-4121 will provide stable and reliable wireless connectivity, even in harsh outdoor environments.
Grid List

10 of 28 products

per page
Page:
  1. 1
  2. 2
  3. 3